Tach stopped
#11
Guest
Posts: n/a
Re: Tach stopped and CEL codes
Tony, Thanks you were right on. I went to AudiWorld.com and found the
procedure for pulling the codes Via the Fuel Pump Relay "fuse trick".
What I got were three codes I hope someone can ID for me. They are
2142, 2223 and 2232.
On Thu, 02 Nov 2006 01:34:55 -0600, Tony <tonyjnospam@nospamvisi.com>
wrote:
>
>
>Phantom@NotHome.yet wrote:
>> I have a 88' Audi 90 non Quattro with 2.3 (NG) and 5speed. Last week
>> the tach stopped working. Where does the tach get it's signal from.
>> The wiring diagram I have says the "Speed sensor" but doesn't give a
>> hint as to where it is.
>> Also I get a check engine light for about 3 mo that I can't seem to
>> figure out. All sensors seem to be working. I average 33.1 MPG on Reg
>> gas. O2 sensor voltage changes when I enrich or lean out the fuel
>> mixture. Any help is appreciated as I want to fix this before the
>> snow starts and things get worse.
>
>I don't remember for sure and I don't have the manuals anymore but it seems to
>me that the tach signal comes from the ECU. That was located in the passenger
>kick panel on the larger T4 series with that engine (had four of them).
>
>To check the codes I would suggest going to AudiWorld and checking the history
>on the forum for your model. Some of the T44s had a place on the top of the fuel
>pump relay where you insert a fuse when the CEL is lighted to get the codes to
>flash on the CEL light. At that point you will need a code reference to find out
>what is wrong.
procedure for pulling the codes Via the Fuel Pump Relay "fuse trick".
What I got were three codes I hope someone can ID for me. They are
2142, 2223 and 2232.
On Thu, 02 Nov 2006 01:34:55 -0600, Tony <tonyjnospam@nospamvisi.com>
wrote:
>
>
>Phantom@NotHome.yet wrote:
>> I have a 88' Audi 90 non Quattro with 2.3 (NG) and 5speed. Last week
>> the tach stopped working. Where does the tach get it's signal from.
>> The wiring diagram I have says the "Speed sensor" but doesn't give a
>> hint as to where it is.
>> Also I get a check engine light for about 3 mo that I can't seem to
>> figure out. All sensors seem to be working. I average 33.1 MPG on Reg
>> gas. O2 sensor voltage changes when I enrich or lean out the fuel
>> mixture. Any help is appreciated as I want to fix this before the
>> snow starts and things get worse.
>
>I don't remember for sure and I don't have the manuals anymore but it seems to
>me that the tach signal comes from the ECU. That was located in the passenger
>kick panel on the larger T4 series with that engine (had four of them).
>
>To check the codes I would suggest going to AudiWorld and checking the history
>on the forum for your model. Some of the T44s had a place on the top of the fuel
>pump relay where you insert a fuse when the CEL is lighted to get the codes to
>flash on the CEL light. At that point you will need a code reference to find out
>what is wrong.
#12
Guest
Posts: n/a
Re: Tach stopped and CEL codes
Good to see you got the codes pulled. Not having the manuals any more I can't
help with what they mean. If someone here doesn't have the information you might
try to post the codes and ask for help on AudiWorld again.
Keep us advised of your progress.
Phantom@NotHome.yet wrote:
> Tony, Thanks you were right on. I went to AudiWorld.com and found the
> procedure for pulling the codes Via the Fuel Pump Relay "fuse trick".
> What I got were three codes I hope someone can ID for me. They are
> 2142, 2223 and 2232.
>
> On Thu, 02 Nov 2006 01:34:55 -0600, Tony <tonyjnospam@nospamvisi.com>
> wrote:
>
>
>>
>>Phantom@NotHome.yet wrote:
>>
>>>I have a 88' Audi 90 non Quattro with 2.3 (NG) and 5speed. Last week
>>>the tach stopped working. Where does the tach get it's signal from.
>>>The wiring diagram I have says the "Speed sensor" but doesn't give a
>>>hint as to where it is.
>>>Also I get a check engine light for about 3 mo that I can't seem to
>>>figure out. All sensors seem to be working. I average 33.1 MPG on Reg
>>>gas. O2 sensor voltage changes when I enrich or lean out the fuel
>>>mixture. Any help is appreciated as I want to fix this before the
>>>snow starts and things get worse.
>>
>>I don't remember for sure and I don't have the manuals anymore but it seems to
>>me that the tach signal comes from the ECU. That was located in the passenger
>>kick panel on the larger T4 series with that engine (had four of them).
>>
>>To check the codes I would suggest going to AudiWorld and checking the history
>>on the forum for your model. Some of the T44s had a place on the top of the fuel
>>pump relay where you insert a fuse when the CEL is lighted to get the codes to
>>flash on the CEL light. At that point you will need a code reference to find out
>>what is wrong.
help with what they mean. If someone here doesn't have the information you might
try to post the codes and ask for help on AudiWorld again.
Keep us advised of your progress.
Phantom@NotHome.yet wrote:
> Tony, Thanks you were right on. I went to AudiWorld.com and found the
> procedure for pulling the codes Via the Fuel Pump Relay "fuse trick".
> What I got were three codes I hope someone can ID for me. They are
> 2142, 2223 and 2232.
>
> On Thu, 02 Nov 2006 01:34:55 -0600, Tony <tonyjnospam@nospamvisi.com>
> wrote:
>
>
>>
>>Phantom@NotHome.yet wrote:
>>
>>>I have a 88' Audi 90 non Quattro with 2.3 (NG) and 5speed. Last week
>>>the tach stopped working. Where does the tach get it's signal from.
>>>The wiring diagram I have says the "Speed sensor" but doesn't give a
>>>hint as to where it is.
>>>Also I get a check engine light for about 3 mo that I can't seem to
>>>figure out. All sensors seem to be working. I average 33.1 MPG on Reg
>>>gas. O2 sensor voltage changes when I enrich or lean out the fuel
>>>mixture. Any help is appreciated as I want to fix this before the
>>>snow starts and things get worse.
>>
>>I don't remember for sure and I don't have the manuals anymore but it seems to
>>me that the tach signal comes from the ECU. That was located in the passenger
>>kick panel on the larger T4 series with that engine (had four of them).
>>
>>To check the codes I would suggest going to AudiWorld and checking the history
>>on the forum for your model. Some of the T44s had a place on the top of the fuel
>>pump relay where you insert a fuse when the CEL is lighted to get the codes to
>>flash on the CEL light. At that point you will need a code reference to find out
>>what is wrong.
#13
Guest
Posts: n/a
Re: Tach stopped and CEL codes
Good to see you got the codes pulled. Not having the manuals any more I can't
help with what they mean. If someone here doesn't have the information you might
try to post the codes and ask for help on AudiWorld again.
Keep us advised of your progress.
Phantom@NotHome.yet wrote:
> Tony, Thanks you were right on. I went to AudiWorld.com and found the
> procedure for pulling the codes Via the Fuel Pump Relay "fuse trick".
> What I got were three codes I hope someone can ID for me. They are
> 2142, 2223 and 2232.
>
> On Thu, 02 Nov 2006 01:34:55 -0600, Tony <tonyjnospam@nospamvisi.com>
> wrote:
>
>
>>
>>Phantom@NotHome.yet wrote:
>>
>>>I have a 88' Audi 90 non Quattro with 2.3 (NG) and 5speed. Last week
>>>the tach stopped working. Where does the tach get it's signal from.
>>>The wiring diagram I have says the "Speed sensor" but doesn't give a
>>>hint as to where it is.
>>>Also I get a check engine light for about 3 mo that I can't seem to
>>>figure out. All sensors seem to be working. I average 33.1 MPG on Reg
>>>gas. O2 sensor voltage changes when I enrich or lean out the fuel
>>>mixture. Any help is appreciated as I want to fix this before the
>>>snow starts and things get worse.
>>
>>I don't remember for sure and I don't have the manuals anymore but it seems to
>>me that the tach signal comes from the ECU. That was located in the passenger
>>kick panel on the larger T4 series with that engine (had four of them).
>>
>>To check the codes I would suggest going to AudiWorld and checking the history
>>on the forum for your model. Some of the T44s had a place on the top of the fuel
>>pump relay where you insert a fuse when the CEL is lighted to get the codes to
>>flash on the CEL light. At that point you will need a code reference to find out
>>what is wrong.
help with what they mean. If someone here doesn't have the information you might
try to post the codes and ask for help on AudiWorld again.
Keep us advised of your progress.
Phantom@NotHome.yet wrote:
> Tony, Thanks you were right on. I went to AudiWorld.com and found the
> procedure for pulling the codes Via the Fuel Pump Relay "fuse trick".
> What I got were three codes I hope someone can ID for me. They are
> 2142, 2223 and 2232.
>
> On Thu, 02 Nov 2006 01:34:55 -0600, Tony <tonyjnospam@nospamvisi.com>
> wrote:
>
>
>>
>>Phantom@NotHome.yet wrote:
>>
>>>I have a 88' Audi 90 non Quattro with 2.3 (NG) and 5speed. Last week
>>>the tach stopped working. Where does the tach get it's signal from.
>>>The wiring diagram I have says the "Speed sensor" but doesn't give a
>>>hint as to where it is.
>>>Also I get a check engine light for about 3 mo that I can't seem to
>>>figure out. All sensors seem to be working. I average 33.1 MPG on Reg
>>>gas. O2 sensor voltage changes when I enrich or lean out the fuel
>>>mixture. Any help is appreciated as I want to fix this before the
>>>snow starts and things get worse.
>>
>>I don't remember for sure and I don't have the manuals anymore but it seems to
>>me that the tach signal comes from the ECU. That was located in the passenger
>>kick panel on the larger T4 series with that engine (had four of them).
>>
>>To check the codes I would suggest going to AudiWorld and checking the history
>>on the forum for your model. Some of the T44s had a place on the top of the fuel
>>pump relay where you insert a fuse when the CEL is lighted to get the codes to
>>flash on the CEL light. At that point you will need a code reference to find out
>>what is wrong.
#14
Guest
Posts: n/a
Re: Tach stopped and CEL codes
Good to see you got the codes pulled. Not having the manuals any more I can't
help with what they mean. If someone here doesn't have the information you might
try to post the codes and ask for help on AudiWorld again.
Keep us advised of your progress.
Phantom@NotHome.yet wrote:
> Tony, Thanks you were right on. I went to AudiWorld.com and found the
> procedure for pulling the codes Via the Fuel Pump Relay "fuse trick".
> What I got were three codes I hope someone can ID for me. They are
> 2142, 2223 and 2232.
>
> On Thu, 02 Nov 2006 01:34:55 -0600, Tony <tonyjnospam@nospamvisi.com>
> wrote:
>
>
>>
>>Phantom@NotHome.yet wrote:
>>
>>>I have a 88' Audi 90 non Quattro with 2.3 (NG) and 5speed. Last week
>>>the tach stopped working. Where does the tach get it's signal from.
>>>The wiring diagram I have says the "Speed sensor" but doesn't give a
>>>hint as to where it is.
>>>Also I get a check engine light for about 3 mo that I can't seem to
>>>figure out. All sensors seem to be working. I average 33.1 MPG on Reg
>>>gas. O2 sensor voltage changes when I enrich or lean out the fuel
>>>mixture. Any help is appreciated as I want to fix this before the
>>>snow starts and things get worse.
>>
>>I don't remember for sure and I don't have the manuals anymore but it seems to
>>me that the tach signal comes from the ECU. That was located in the passenger
>>kick panel on the larger T4 series with that engine (had four of them).
>>
>>To check the codes I would suggest going to AudiWorld and checking the history
>>on the forum for your model. Some of the T44s had a place on the top of the fuel
>>pump relay where you insert a fuse when the CEL is lighted to get the codes to
>>flash on the CEL light. At that point you will need a code reference to find out
>>what is wrong.
help with what they mean. If someone here doesn't have the information you might
try to post the codes and ask for help on AudiWorld again.
Keep us advised of your progress.
Phantom@NotHome.yet wrote:
> Tony, Thanks you were right on. I went to AudiWorld.com and found the
> procedure for pulling the codes Via the Fuel Pump Relay "fuse trick".
> What I got were three codes I hope someone can ID for me. They are
> 2142, 2223 and 2232.
>
> On Thu, 02 Nov 2006 01:34:55 -0600, Tony <tonyjnospam@nospamvisi.com>
> wrote:
>
>
>>
>>Phantom@NotHome.yet wrote:
>>
>>>I have a 88' Audi 90 non Quattro with 2.3 (NG) and 5speed. Last week
>>>the tach stopped working. Where does the tach get it's signal from.
>>>The wiring diagram I have says the "Speed sensor" but doesn't give a
>>>hint as to where it is.
>>>Also I get a check engine light for about 3 mo that I can't seem to
>>>figure out. All sensors seem to be working. I average 33.1 MPG on Reg
>>>gas. O2 sensor voltage changes when I enrich or lean out the fuel
>>>mixture. Any help is appreciated as I want to fix this before the
>>>snow starts and things get worse.
>>
>>I don't remember for sure and I don't have the manuals anymore but it seems to
>>me that the tach signal comes from the ECU. That was located in the passenger
>>kick panel on the larger T4 series with that engine (had four of them).
>>
>>To check the codes I would suggest going to AudiWorld and checking the history
>>on the forum for your model. Some of the T44s had a place on the top of the fuel
>>pump relay where you insert a fuse when the CEL is lighted to get the codes to
>>flash on the CEL light. At that point you will need a code reference to find out
>>what is wrong.
#15
Guest
Posts: n/a
Re: Tach stopped and CEL codes
Good to see you got the codes pulled. Not having the manuals any more I can't
help with what they mean. If someone here doesn't have the information you might
try to post the codes and ask for help on AudiWorld again.
Keep us advised of your progress.
Phantom@NotHome.yet wrote:
> Tony, Thanks you were right on. I went to AudiWorld.com and found the
> procedure for pulling the codes Via the Fuel Pump Relay "fuse trick".
> What I got were three codes I hope someone can ID for me. They are
> 2142, 2223 and 2232.
>
> On Thu, 02 Nov 2006 01:34:55 -0600, Tony <tonyjnospam@nospamvisi.com>
> wrote:
>
>
>>
>>Phantom@NotHome.yet wrote:
>>
>>>I have a 88' Audi 90 non Quattro with 2.3 (NG) and 5speed. Last week
>>>the tach stopped working. Where does the tach get it's signal from.
>>>The wiring diagram I have says the "Speed sensor" but doesn't give a
>>>hint as to where it is.
>>>Also I get a check engine light for about 3 mo that I can't seem to
>>>figure out. All sensors seem to be working. I average 33.1 MPG on Reg
>>>gas. O2 sensor voltage changes when I enrich or lean out the fuel
>>>mixture. Any help is appreciated as I want to fix this before the
>>>snow starts and things get worse.
>>
>>I don't remember for sure and I don't have the manuals anymore but it seems to
>>me that the tach signal comes from the ECU. That was located in the passenger
>>kick panel on the larger T4 series with that engine (had four of them).
>>
>>To check the codes I would suggest going to AudiWorld and checking the history
>>on the forum for your model. Some of the T44s had a place on the top of the fuel
>>pump relay where you insert a fuse when the CEL is lighted to get the codes to
>>flash on the CEL light. At that point you will need a code reference to find out
>>what is wrong.
help with what they mean. If someone here doesn't have the information you might
try to post the codes and ask for help on AudiWorld again.
Keep us advised of your progress.
Phantom@NotHome.yet wrote:
> Tony, Thanks you were right on. I went to AudiWorld.com and found the
> procedure for pulling the codes Via the Fuel Pump Relay "fuse trick".
> What I got were three codes I hope someone can ID for me. They are
> 2142, 2223 and 2232.
>
> On Thu, 02 Nov 2006 01:34:55 -0600, Tony <tonyjnospam@nospamvisi.com>
> wrote:
>
>
>>
>>Phantom@NotHome.yet wrote:
>>
>>>I have a 88' Audi 90 non Quattro with 2.3 (NG) and 5speed. Last week
>>>the tach stopped working. Where does the tach get it's signal from.
>>>The wiring diagram I have says the "Speed sensor" but doesn't give a
>>>hint as to where it is.
>>>Also I get a check engine light for about 3 mo that I can't seem to
>>>figure out. All sensors seem to be working. I average 33.1 MPG on Reg
>>>gas. O2 sensor voltage changes when I enrich or lean out the fuel
>>>mixture. Any help is appreciated as I want to fix this before the
>>>snow starts and things get worse.
>>
>>I don't remember for sure and I don't have the manuals anymore but it seems to
>>me that the tach signal comes from the ECU. That was located in the passenger
>>kick panel on the larger T4 series with that engine (had four of them).
>>
>>To check the codes I would suggest going to AudiWorld and checking the history
>>on the forum for your model. Some of the T44s had a place on the top of the fuel
>>pump relay where you insert a fuse when the CEL is lighted to get the codes to
>>flash on the CEL light. At that point you will need a code reference to find out
>>what is wrong.
#16
Guest
Posts: n/a
Re: Tach stopped and CEL codes
googled and here
http://www.intendedacceleration.com/fault_codes.html
2142
Knock Sensor (KS) #1 (G 61)
Open or short circuit, Defective sensor
Check sensor and wiring
Symptom: Timing retarded, High fuel consumption, power loss, Boost pressure
not attained
2223
Barometric Pressure Sensor ( F 96)
2232?
"TonyJ" <tonyjnospam@nospamvisi.com> wrote in message
news:12nkjda6tq4fabc@corp.supernews.com...
> Good to see you got the codes pulled. Not having the manuals any more I
> can't help with what they mean. If someone here doesn't have the
> information you might try to post the codes and ask for help on AudiWorld
> again.
>
> Keep us advised of your progress.
>
> Phantom@NotHome.yet wrote:
>
>> Tony, Thanks you were right on. I went to AudiWorld.com and found the
>> procedure for pulling the codes Via the Fuel Pump Relay "fuse trick".
>> What I got were three codes I hope someone can ID for me. They are
>> 2142, 2223 and 2232.
>>
>> On Thu, 02 Nov 2006 01:34:55 -0600, Tony <tonyjnospam@nospamvisi.com>
>> wrote:
>>
>>
>>>
>>>Phantom@NotHome.yet wrote:
>>>
>>>>I have a 88' Audi 90 non Quattro with 2.3 (NG) and 5speed. Last week
>>>>the tach stopped working. Where does the tach get it's signal from.
>>>>The wiring diagram I have says the "Speed sensor" but doesn't give a
>>>>hint as to where it is.
>>>>Also I get a check engine light for about 3 mo that I can't seem to
>>>>figure out. All sensors seem to be working. I average 33.1 MPG on Reg
>>>>gas. O2 sensor voltage changes when I enrich or lean out the fuel
>>>>mixture. Any help is appreciated as I want to fix this before the
>>>>snow starts and things get worse.
>>>
>>>I don't remember for sure and I don't have the manuals anymore but it
>>>seems to me that the tach signal comes from the ECU. That was located in
>>>the passenger kick panel on the larger T4 series with that engine (had
>>>four of them).
>>>
>>>To check the codes I would suggest going to AudiWorld and checking the
>>>history on the forum for your model. Some of the T44s had a place on the
>>>top of the fuel pump relay where you insert a fuse when the CEL is
>>>lighted to get the codes to flash on the CEL light. At that point you
>>>will need a code reference to find out what is wrong.
http://www.intendedacceleration.com/fault_codes.html
2142
Knock Sensor (KS) #1 (G 61)
Open or short circuit, Defective sensor
Check sensor and wiring
Symptom: Timing retarded, High fuel consumption, power loss, Boost pressure
not attained
2223
Barometric Pressure Sensor ( F 96)
2232?
"TonyJ" <tonyjnospam@nospamvisi.com> wrote in message
news:12nkjda6tq4fabc@corp.supernews.com...
> Good to see you got the codes pulled. Not having the manuals any more I
> can't help with what they mean. If someone here doesn't have the
> information you might try to post the codes and ask for help on AudiWorld
> again.
>
> Keep us advised of your progress.
>
> Phantom@NotHome.yet wrote:
>
>> Tony, Thanks you were right on. I went to AudiWorld.com and found the
>> procedure for pulling the codes Via the Fuel Pump Relay "fuse trick".
>> What I got were three codes I hope someone can ID for me. They are
>> 2142, 2223 and 2232.
>>
>> On Thu, 02 Nov 2006 01:34:55 -0600, Tony <tonyjnospam@nospamvisi.com>
>> wrote:
>>
>>
>>>
>>>Phantom@NotHome.yet wrote:
>>>
>>>>I have a 88' Audi 90 non Quattro with 2.3 (NG) and 5speed. Last week
>>>>the tach stopped working. Where does the tach get it's signal from.
>>>>The wiring diagram I have says the "Speed sensor" but doesn't give a
>>>>hint as to where it is.
>>>>Also I get a check engine light for about 3 mo that I can't seem to
>>>>figure out. All sensors seem to be working. I average 33.1 MPG on Reg
>>>>gas. O2 sensor voltage changes when I enrich or lean out the fuel
>>>>mixture. Any help is appreciated as I want to fix this before the
>>>>snow starts and things get worse.
>>>
>>>I don't remember for sure and I don't have the manuals anymore but it
>>>seems to me that the tach signal comes from the ECU. That was located in
>>>the passenger kick panel on the larger T4 series with that engine (had
>>>four of them).
>>>
>>>To check the codes I would suggest going to AudiWorld and checking the
>>>history on the forum for your model. Some of the T44s had a place on the
>>>top of the fuel pump relay where you insert a fuse when the CEL is
>>>lighted to get the codes to flash on the CEL light. At that point you
>>>will need a code reference to find out what is wrong.
#17
Guest
Posts: n/a
Re: Tach stopped and CEL codes
googled and here
http://www.intendedacceleration.com/fault_codes.html
2142
Knock Sensor (KS) #1 (G 61)
Open or short circuit, Defective sensor
Check sensor and wiring
Symptom: Timing retarded, High fuel consumption, power loss, Boost pressure
not attained
2223
Barometric Pressure Sensor ( F 96)
2232?
"TonyJ" <tonyjnospam@nospamvisi.com> wrote in message
news:12nkjda6tq4fabc@corp.supernews.com...
> Good to see you got the codes pulled. Not having the manuals any more I
> can't help with what they mean. If someone here doesn't have the
> information you might try to post the codes and ask for help on AudiWorld
> again.
>
> Keep us advised of your progress.
>
> Phantom@NotHome.yet wrote:
>
>> Tony, Thanks you were right on. I went to AudiWorld.com and found the
>> procedure for pulling the codes Via the Fuel Pump Relay "fuse trick".
>> What I got were three codes I hope someone can ID for me. They are
>> 2142, 2223 and 2232.
>>
>> On Thu, 02 Nov 2006 01:34:55 -0600, Tony <tonyjnospam@nospamvisi.com>
>> wrote:
>>
>>
>>>
>>>Phantom@NotHome.yet wrote:
>>>
>>>>I have a 88' Audi 90 non Quattro with 2.3 (NG) and 5speed. Last week
>>>>the tach stopped working. Where does the tach get it's signal from.
>>>>The wiring diagram I have says the "Speed sensor" but doesn't give a
>>>>hint as to where it is.
>>>>Also I get a check engine light for about 3 mo that I can't seem to
>>>>figure out. All sensors seem to be working. I average 33.1 MPG on Reg
>>>>gas. O2 sensor voltage changes when I enrich or lean out the fuel
>>>>mixture. Any help is appreciated as I want to fix this before the
>>>>snow starts and things get worse.
>>>
>>>I don't remember for sure and I don't have the manuals anymore but it
>>>seems to me that the tach signal comes from the ECU. That was located in
>>>the passenger kick panel on the larger T4 series with that engine (had
>>>four of them).
>>>
>>>To check the codes I would suggest going to AudiWorld and checking the
>>>history on the forum for your model. Some of the T44s had a place on the
>>>top of the fuel pump relay where you insert a fuse when the CEL is
>>>lighted to get the codes to flash on the CEL light. At that point you
>>>will need a code reference to find out what is wrong.
http://www.intendedacceleration.com/fault_codes.html
2142
Knock Sensor (KS) #1 (G 61)
Open or short circuit, Defective sensor
Check sensor and wiring
Symptom: Timing retarded, High fuel consumption, power loss, Boost pressure
not attained
2223
Barometric Pressure Sensor ( F 96)
2232?
"TonyJ" <tonyjnospam@nospamvisi.com> wrote in message
news:12nkjda6tq4fabc@corp.supernews.com...
> Good to see you got the codes pulled. Not having the manuals any more I
> can't help with what they mean. If someone here doesn't have the
> information you might try to post the codes and ask for help on AudiWorld
> again.
>
> Keep us advised of your progress.
>
> Phantom@NotHome.yet wrote:
>
>> Tony, Thanks you were right on. I went to AudiWorld.com and found the
>> procedure for pulling the codes Via the Fuel Pump Relay "fuse trick".
>> What I got were three codes I hope someone can ID for me. They are
>> 2142, 2223 and 2232.
>>
>> On Thu, 02 Nov 2006 01:34:55 -0600, Tony <tonyjnospam@nospamvisi.com>
>> wrote:
>>
>>
>>>
>>>Phantom@NotHome.yet wrote:
>>>
>>>>I have a 88' Audi 90 non Quattro with 2.3 (NG) and 5speed. Last week
>>>>the tach stopped working. Where does the tach get it's signal from.
>>>>The wiring diagram I have says the "Speed sensor" but doesn't give a
>>>>hint as to where it is.
>>>>Also I get a check engine light for about 3 mo that I can't seem to
>>>>figure out. All sensors seem to be working. I average 33.1 MPG on Reg
>>>>gas. O2 sensor voltage changes when I enrich or lean out the fuel
>>>>mixture. Any help is appreciated as I want to fix this before the
>>>>snow starts and things get worse.
>>>
>>>I don't remember for sure and I don't have the manuals anymore but it
>>>seems to me that the tach signal comes from the ECU. That was located in
>>>the passenger kick panel on the larger T4 series with that engine (had
>>>four of them).
>>>
>>>To check the codes I would suggest going to AudiWorld and checking the
>>>history on the forum for your model. Some of the T44s had a place on the
>>>top of the fuel pump relay where you insert a fuse when the CEL is
>>>lighted to get the codes to flash on the CEL light. At that point you
>>>will need a code reference to find out what is wrong.
#18
Guest
Posts: n/a
Re: Tach stopped and CEL codes
googled and here
http://www.intendedacceleration.com/fault_codes.html
2142
Knock Sensor (KS) #1 (G 61)
Open or short circuit, Defective sensor
Check sensor and wiring
Symptom: Timing retarded, High fuel consumption, power loss, Boost pressure
not attained
2223
Barometric Pressure Sensor ( F 96)
2232?
"TonyJ" <tonyjnospam@nospamvisi.com> wrote in message
news:12nkjda6tq4fabc@corp.supernews.com...
> Good to see you got the codes pulled. Not having the manuals any more I
> can't help with what they mean. If someone here doesn't have the
> information you might try to post the codes and ask for help on AudiWorld
> again.
>
> Keep us advised of your progress.
>
> Phantom@NotHome.yet wrote:
>
>> Tony, Thanks you were right on. I went to AudiWorld.com and found the
>> procedure for pulling the codes Via the Fuel Pump Relay "fuse trick".
>> What I got were three codes I hope someone can ID for me. They are
>> 2142, 2223 and 2232.
>>
>> On Thu, 02 Nov 2006 01:34:55 -0600, Tony <tonyjnospam@nospamvisi.com>
>> wrote:
>>
>>
>>>
>>>Phantom@NotHome.yet wrote:
>>>
>>>>I have a 88' Audi 90 non Quattro with 2.3 (NG) and 5speed. Last week
>>>>the tach stopped working. Where does the tach get it's signal from.
>>>>The wiring diagram I have says the "Speed sensor" but doesn't give a
>>>>hint as to where it is.
>>>>Also I get a check engine light for about 3 mo that I can't seem to
>>>>figure out. All sensors seem to be working. I average 33.1 MPG on Reg
>>>>gas. O2 sensor voltage changes when I enrich or lean out the fuel
>>>>mixture. Any help is appreciated as I want to fix this before the
>>>>snow starts and things get worse.
>>>
>>>I don't remember for sure and I don't have the manuals anymore but it
>>>seems to me that the tach signal comes from the ECU. That was located in
>>>the passenger kick panel on the larger T4 series with that engine (had
>>>four of them).
>>>
>>>To check the codes I would suggest going to AudiWorld and checking the
>>>history on the forum for your model. Some of the T44s had a place on the
>>>top of the fuel pump relay where you insert a fuse when the CEL is
>>>lighted to get the codes to flash on the CEL light. At that point you
>>>will need a code reference to find out what is wrong.
http://www.intendedacceleration.com/fault_codes.html
2142
Knock Sensor (KS) #1 (G 61)
Open or short circuit, Defective sensor
Check sensor and wiring
Symptom: Timing retarded, High fuel consumption, power loss, Boost pressure
not attained
2223
Barometric Pressure Sensor ( F 96)
2232?
"TonyJ" <tonyjnospam@nospamvisi.com> wrote in message
news:12nkjda6tq4fabc@corp.supernews.com...
> Good to see you got the codes pulled. Not having the manuals any more I
> can't help with what they mean. If someone here doesn't have the
> information you might try to post the codes and ask for help on AudiWorld
> again.
>
> Keep us advised of your progress.
>
> Phantom@NotHome.yet wrote:
>
>> Tony, Thanks you were right on. I went to AudiWorld.com and found the
>> procedure for pulling the codes Via the Fuel Pump Relay "fuse trick".
>> What I got were three codes I hope someone can ID for me. They are
>> 2142, 2223 and 2232.
>>
>> On Thu, 02 Nov 2006 01:34:55 -0600, Tony <tonyjnospam@nospamvisi.com>
>> wrote:
>>
>>
>>>
>>>Phantom@NotHome.yet wrote:
>>>
>>>>I have a 88' Audi 90 non Quattro with 2.3 (NG) and 5speed. Last week
>>>>the tach stopped working. Where does the tach get it's signal from.
>>>>The wiring diagram I have says the "Speed sensor" but doesn't give a
>>>>hint as to where it is.
>>>>Also I get a check engine light for about 3 mo that I can't seem to
>>>>figure out. All sensors seem to be working. I average 33.1 MPG on Reg
>>>>gas. O2 sensor voltage changes when I enrich or lean out the fuel
>>>>mixture. Any help is appreciated as I want to fix this before the
>>>>snow starts and things get worse.
>>>
>>>I don't remember for sure and I don't have the manuals anymore but it
>>>seems to me that the tach signal comes from the ECU. That was located in
>>>the passenger kick panel on the larger T4 series with that engine (had
>>>four of them).
>>>
>>>To check the codes I would suggest going to AudiWorld and checking the
>>>history on the forum for your model. Some of the T44s had a place on the
>>>top of the fuel pump relay where you insert a fuse when the CEL is
>>>lighted to get the codes to flash on the CEL light. At that point you
>>>will need a code reference to find out what is wrong.
#19
Guest
Posts: n/a
Re: Tach stopped and CEL codes
googled and here
http://www.intendedacceleration.com/fault_codes.html
2142
Knock Sensor (KS) #1 (G 61)
Open or short circuit, Defective sensor
Check sensor and wiring
Symptom: Timing retarded, High fuel consumption, power loss, Boost pressure
not attained
2223
Barometric Pressure Sensor ( F 96)
2232?
"TonyJ" <tonyjnospam@nospamvisi.com> wrote in message
news:12nkjda6tq4fabc@corp.supernews.com...
> Good to see you got the codes pulled. Not having the manuals any more I
> can't help with what they mean. If someone here doesn't have the
> information you might try to post the codes and ask for help on AudiWorld
> again.
>
> Keep us advised of your progress.
>
> Phantom@NotHome.yet wrote:
>
>> Tony, Thanks you were right on. I went to AudiWorld.com and found the
>> procedure for pulling the codes Via the Fuel Pump Relay "fuse trick".
>> What I got were three codes I hope someone can ID for me. They are
>> 2142, 2223 and 2232.
>>
>> On Thu, 02 Nov 2006 01:34:55 -0600, Tony <tonyjnospam@nospamvisi.com>
>> wrote:
>>
>>
>>>
>>>Phantom@NotHome.yet wrote:
>>>
>>>>I have a 88' Audi 90 non Quattro with 2.3 (NG) and 5speed. Last week
>>>>the tach stopped working. Where does the tach get it's signal from.
>>>>The wiring diagram I have says the "Speed sensor" but doesn't give a
>>>>hint as to where it is.
>>>>Also I get a check engine light for about 3 mo that I can't seem to
>>>>figure out. All sensors seem to be working. I average 33.1 MPG on Reg
>>>>gas. O2 sensor voltage changes when I enrich or lean out the fuel
>>>>mixture. Any help is appreciated as I want to fix this before the
>>>>snow starts and things get worse.
>>>
>>>I don't remember for sure and I don't have the manuals anymore but it
>>>seems to me that the tach signal comes from the ECU. That was located in
>>>the passenger kick panel on the larger T4 series with that engine (had
>>>four of them).
>>>
>>>To check the codes I would suggest going to AudiWorld and checking the
>>>history on the forum for your model. Some of the T44s had a place on the
>>>top of the fuel pump relay where you insert a fuse when the CEL is
>>>lighted to get the codes to flash on the CEL light. At that point you
>>>will need a code reference to find out what is wrong.
http://www.intendedacceleration.com/fault_codes.html
2142
Knock Sensor (KS) #1 (G 61)
Open or short circuit, Defective sensor
Check sensor and wiring
Symptom: Timing retarded, High fuel consumption, power loss, Boost pressure
not attained
2223
Barometric Pressure Sensor ( F 96)
2232?
"TonyJ" <tonyjnospam@nospamvisi.com> wrote in message
news:12nkjda6tq4fabc@corp.supernews.com...
> Good to see you got the codes pulled. Not having the manuals any more I
> can't help with what they mean. If someone here doesn't have the
> information you might try to post the codes and ask for help on AudiWorld
> again.
>
> Keep us advised of your progress.
>
> Phantom@NotHome.yet wrote:
>
>> Tony, Thanks you were right on. I went to AudiWorld.com and found the
>> procedure for pulling the codes Via the Fuel Pump Relay "fuse trick".
>> What I got were three codes I hope someone can ID for me. They are
>> 2142, 2223 and 2232.
>>
>> On Thu, 02 Nov 2006 01:34:55 -0600, Tony <tonyjnospam@nospamvisi.com>
>> wrote:
>>
>>
>>>
>>>Phantom@NotHome.yet wrote:
>>>
>>>>I have a 88' Audi 90 non Quattro with 2.3 (NG) and 5speed. Last week
>>>>the tach stopped working. Where does the tach get it's signal from.
>>>>The wiring diagram I have says the "Speed sensor" but doesn't give a
>>>>hint as to where it is.
>>>>Also I get a check engine light for about 3 mo that I can't seem to
>>>>figure out. All sensors seem to be working. I average 33.1 MPG on Reg
>>>>gas. O2 sensor voltage changes when I enrich or lean out the fuel
>>>>mixture. Any help is appreciated as I want to fix this before the
>>>>snow starts and things get worse.
>>>
>>>I don't remember for sure and I don't have the manuals anymore but it
>>>seems to me that the tach signal comes from the ECU. That was located in
>>>the passenger kick panel on the larger T4 series with that engine (had
>>>four of them).
>>>
>>>To check the codes I would suggest going to AudiWorld and checking the
>>>history on the forum for your model. Some of the T44s had a place on the
>>>top of the fuel pump relay where you insert a fuse when the CEL is
>>>lighted to get the codes to flash on the CEL light. At that point you
>>>will need a code reference to find out what is wrong.
Thread
Thread Starter
Forum
Replies
Last Post
Sami Heikkinen
Audi Mailing List
52
12-18-2005 06:08 PM
Ottar Tverberg
Audi Mailing List
0
03-04-2004 01:24 PM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)