mattl

I recently purchased a 1998 A4 1.6se, the water temperature gauge does not
seem to move at all!

Are there any things I can check myself before taking it into the dealers?

Any help appreciated.

Cheers
Matt

Christopher Roberts

Most likely someone has removed the connector from the sensor and forgot to
replace it. Or the sensor has failed. If I recall correctly it's on the
right of the engine towards the rear. Just look for a loose connection or a
cut wire!

--
Christopher Roberts

"mattl" <matthew.lauezzari@NOSPAMntlworld.com> wrote in message
news:XA8Tb.276$PE1.200@newsfep1-gui.server.ntli.net...
> I recently purchased a 1998 A4 1.6se, the water temperature gauge does not
> seem to move at all!
>
> Are there any things I can check myself before taking it into the dealers?
>
> Any help appreciated.
>
> Cheers
> Matt
>
>

mattl

"Christopher Roberts" <spamtrap@anywhere.com> wrote in message
news:BKoTb.4120$xc4.38367452@news-text.cableinet.net...
> Most likely someone has removed the connector from the sensor and forgot
to
> replace it. Or the sensor has failed. If I recall correctly it's on the
> right of the engine towards the rear. Just look for a loose connection or
a
> cut wire!

I'll take a look thanks, any other advice gratefully received!

Mike Buckley

From discussion on the more specialist / technically orientated Audi
web-sites, it would appear that the temp sender on 80's and the like are
regarded as being suspect. It would be fair to assume that the problem may
well apply to later models as well.

Apart from the obvious (but perhaps unlikely) loose/cut wires, the only
other checks you can make are to wiggle the plug and see if that helps.
Certainly on my car (an old 80 with a similar problem) I eventually found
the correct sender (grey - 3 pin) and eventually identified three wires
below the rubber cap on the plug - one was obviously an earth as it gave no
reading on a circuit tester - another gave a steady pulse (no idea what for)
and the third gave a steady reading. On earthing that one, the temp gauge
ran to red - which proved the gauge worked, although I suspect it may be
"sticky" - another known problem apparently.

You could try this - but don't blame me if you blow something expensive! I'd
pop into the local Audi dealer and ask nicely if someone can spare 10 mins
to put their gauge-tester on it - that at least will help identify whether
its the gauge or the sender. If its the sender, and if it's the same set-up
as the 80, it's a 30 second job (no tools) to change. £25 or so for the
sender though.

Best of luck - I'd be interested in knowing how you get on.

Mike.

mattl <matthew.lauezzari@NOSPAMntlworld.com> wrote in message
news:BOyTb.191$902.113@newsfep1-gui.server.ntli.net...
>
> "Christopher Roberts" <spamtrap@anywhere.com> wrote in message
> news:BKoTb.4120$xc4.38367452@news-text.cableinet.net...
> > Most likely someone has removed the connector from the sensor and forgot
> to
> > replace it. Or the sensor has failed. If I recall correctly it's on the
> > right of the engine towards the rear. Just look for a loose connection
or
> a
> > cut wire!
>
> I'll take a look thanks, any other advice gratefully received!
>
>

mattl

> You could try this - but don't blame me if you blow something expensive!
I'd
> pop into the local Audi dealer and ask nicely if someone can spare 10 mins
> to put their gauge-tester on it - that at least will help identify whether
> its the gauge or the sender. If its the sender, and if it's the same
set-up
> as the 80, it's a 30 second job (no tools) to change. £25 or so for the
> sender though.
>
> Best of luck - I'd be interested in knowing how you get on.


Mike,

Thanks for the advice, I'll post the result as soon as I have time to get
the car to the garage!!!