'90 V8 Quattro Water and Oil Temperature Help
12-06-2004, 04:48 PM
#1
Guest
Posts: n/a
'90 V8 Quattro Water and Oil Temperature Help
My water and oil temperature gauges are both reading 60-65C. From what I've
gathered, the water temperature should be higher, around 90C. I assume the
water and oil gauges should read similar temperatures and since they do, I
assume they are correct.
Is checking the thermostat the reasonable thing to do? Is this a relatively
easy thing for a novice mechanic? Where is the thermostat on this engine?
Thanks,
Tom
gathered, the water temperature should be higher, around 90C. I assume the
water and oil gauges should read similar temperatures and since they do, I
assume they are correct.
Is checking the thermostat the reasonable thing to do? Is this a relatively
easy thing for a novice mechanic? Where is the thermostat on this engine?
Thanks,
Tom
12-09-2004, 02:59 PM
#2
Guest
Posts: n/a
Re: '90 V8 Quattro Water and Oil Temperature Help
On Mon, 6 Dec 2004 16:48:54 -0600, "GigaNews" <tom.quinn@adherentlabs.com>
wrote:
> My water and oil temperature gauges are both reading 60-65C. From what I've
> gathered, the water temperature should be higher, around 90C. I assume the
> water and oil gauges should read similar temperatures and since they do, I
> assume they are correct.
Wayter temp should be near 90C when the engine is hot. My '90 Audi-90 had
chronically low water temp reading and very slow warmup after about the 4th
year during the winter. I suspect that the thermostat was stuck open. It's
a bitch to change on the -90. You have to remove a bunch of stuff to get
the housing off.
Oil tempertature should be a bit higher. Between 200-250 F (95-120C) is
about right when the engine is fully warmed up. You always want the oil to
be close to or above the boiling temperature of water, so that any
condensation in the crankcase is eliminated when the engine is running.
>
> Is checking the thermostat the reasonable thing to do? Is this a relatively
> easy thing for a novice mechanic? Where is the thermostat on this engine?
>
> Thanks,
> Tom
>
wrote:
> My water and oil temperature gauges are both reading 60-65C. From what I've
> gathered, the water temperature should be higher, around 90C. I assume the
> water and oil gauges should read similar temperatures and since they do, I
> assume they are correct.
Wayter temp should be near 90C when the engine is hot. My '90 Audi-90 had
chronically low water temp reading and very slow warmup after about the 4th
year during the winter. I suspect that the thermostat was stuck open. It's
a bitch to change on the -90. You have to remove a bunch of stuff to get
the housing off.
Oil tempertature should be a bit higher. Between 200-250 F (95-120C) is
about right when the engine is fully warmed up. You always want the oil to
be close to or above the boiling temperature of water, so that any
condensation in the crankcase is eliminated when the engine is running.
>
> Is checking the thermostat the reasonable thing to do? Is this a relatively
> easy thing for a novice mechanic? Where is the thermostat on this engine?
>
> Thanks,
> Tom
>
12-09-2004, 02:59 PM
#3
Guest
Posts: n/a
Re: '90 V8 Quattro Water and Oil Temperature Help
On Mon, 6 Dec 2004 16:48:54 -0600, "GigaNews" <tom.quinn@adherentlabs.com>
wrote:
> My water and oil temperature gauges are both reading 60-65C. From what I've
> gathered, the water temperature should be higher, around 90C. I assume the
> water and oil gauges should read similar temperatures and since they do, I
> assume they are correct.
Wayter temp should be near 90C when the engine is hot. My '90 Audi-90 had
chronically low water temp reading and very slow warmup after about the 4th
year during the winter. I suspect that the thermostat was stuck open. It's
a bitch to change on the -90. You have to remove a bunch of stuff to get
the housing off.
Oil tempertature should be a bit higher. Between 200-250 F (95-120C) is
about right when the engine is fully warmed up. You always want the oil to
be close to or above the boiling temperature of water, so that any
condensation in the crankcase is eliminated when the engine is running.
>
> Is checking the thermostat the reasonable thing to do? Is this a relatively
> easy thing for a novice mechanic? Where is the thermostat on this engine?
>
> Thanks,
> Tom
>
wrote:
> My water and oil temperature gauges are both reading 60-65C. From what I've
> gathered, the water temperature should be higher, around 90C. I assume the
> water and oil gauges should read similar temperatures and since they do, I
> assume they are correct.
Wayter temp should be near 90C when the engine is hot. My '90 Audi-90 had
chronically low water temp reading and very slow warmup after about the 4th
year during the winter. I suspect that the thermostat was stuck open. It's
a bitch to change on the -90. You have to remove a bunch of stuff to get
the housing off.
Oil tempertature should be a bit higher. Between 200-250 F (95-120C) is
about right when the engine is fully warmed up. You always want the oil to
be close to or above the boiling temperature of water, so that any
condensation in the crankcase is eliminated when the engine is running.
>
> Is checking the thermostat the reasonable thing to do? Is this a relatively
> easy thing for a novice mechanic? Where is the thermostat on this engine?
>
> Thanks,
> Tom
>
12-09-2004, 02:59 PM
#4
Guest
Posts: n/a
Re: '90 V8 Quattro Water and Oil Temperature Help
On Mon, 6 Dec 2004 16:48:54 -0600, "GigaNews" <tom.quinn@adherentlabs.com>
wrote:
> My water and oil temperature gauges are both reading 60-65C. From what I've
> gathered, the water temperature should be higher, around 90C. I assume the
> water and oil gauges should read similar temperatures and since they do, I
> assume they are correct.
Wayter temp should be near 90C when the engine is hot. My '90 Audi-90 had
chronically low water temp reading and very slow warmup after about the 4th
year during the winter. I suspect that the thermostat was stuck open. It's
a bitch to change on the -90. You have to remove a bunch of stuff to get
the housing off.
Oil tempertature should be a bit higher. Between 200-250 F (95-120C) is
about right when the engine is fully warmed up. You always want the oil to
be close to or above the boiling temperature of water, so that any
condensation in the crankcase is eliminated when the engine is running.
>
> Is checking the thermostat the reasonable thing to do? Is this a relatively
> easy thing for a novice mechanic? Where is the thermostat on this engine?
>
> Thanks,
> Tom
>
wrote:
> My water and oil temperature gauges are both reading 60-65C. From what I've
> gathered, the water temperature should be higher, around 90C. I assume the
> water and oil gauges should read similar temperatures and since they do, I
> assume they are correct.
Wayter temp should be near 90C when the engine is hot. My '90 Audi-90 had
chronically low water temp reading and very slow warmup after about the 4th
year during the winter. I suspect that the thermostat was stuck open. It's
a bitch to change on the -90. You have to remove a bunch of stuff to get
the housing off.
Oil tempertature should be a bit higher. Between 200-250 F (95-120C) is
about right when the engine is fully warmed up. You always want the oil to
be close to or above the boiling temperature of water, so that any
condensation in the crankcase is eliminated when the engine is running.
>
> Is checking the thermostat the reasonable thing to do? Is this a relatively
> easy thing for a novice mechanic? Where is the thermostat on this engine?
>
> Thanks,
> Tom
>
12-09-2004, 05:05 PM
#5
Guest
Posts: n/a
Re: '90 V8 Quattro Water and Oil Temperature Help
So other than a faulty temperature gauge, what could account for a low oil
temperature?
Thanks,
Tom
"Jay Somerset" <jay@hotmail.com> wrote in message
news:3rehr01n6f55ighu29jkr26q53cp2rt1l8@4ax.com...
> On Mon, 6 Dec 2004 16:48:54 -0600, "GigaNews" <tom.quinn@adherentlabs.com>
> wrote:
>
>> My water and oil temperature gauges are both reading 60-65C. From what
>> I've
>> gathered, the water temperature should be higher, around 90C. I assume
>> the
>> water and oil gauges should read similar temperatures and since they do,
>> I
>> assume they are correct.
>
> Wayter temp should be near 90C when the engine is hot. My '90 Audi-90 had
> chronically low water temp reading and very slow warmup after about the
> 4th
> year during the winter. I suspect that the thermostat was stuck open.
> It's
> a bitch to change on the -90. You have to remove a bunch of stuff to get
> the housing off.
>
> Oil tempertature should be a bit higher. Between 200-250 F (95-120C) is
> about right when the engine is fully warmed up. You always want the oil
> to
> be close to or above the boiling temperature of water, so that any
> condensation in the crankcase is eliminated when the engine is running.
>
>>
>> Is checking the thermostat the reasonable thing to do? Is this a
>> relatively
>> easy thing for a novice mechanic? Where is the thermostat on this
>> engine?
>>
>> Thanks,
>> Tom
>>
>
temperature?
Thanks,
Tom
"Jay Somerset" <jay@hotmail.com> wrote in message
news:3rehr01n6f55ighu29jkr26q53cp2rt1l8@4ax.com...
> On Mon, 6 Dec 2004 16:48:54 -0600, "GigaNews" <tom.quinn@adherentlabs.com>
> wrote:
>
>> My water and oil temperature gauges are both reading 60-65C. From what
>> I've
>> gathered, the water temperature should be higher, around 90C. I assume
>> the
>> water and oil gauges should read similar temperatures and since they do,
>> I
>> assume they are correct.
>
> Wayter temp should be near 90C when the engine is hot. My '90 Audi-90 had
> chronically low water temp reading and very slow warmup after about the
> 4th
> year during the winter. I suspect that the thermostat was stuck open.
> It's
> a bitch to change on the -90. You have to remove a bunch of stuff to get
> the housing off.
>
> Oil tempertature should be a bit higher. Between 200-250 F (95-120C) is
> about right when the engine is fully warmed up. You always want the oil
> to
> be close to or above the boiling temperature of water, so that any
> condensation in the crankcase is eliminated when the engine is running.
>
>>
>> Is checking the thermostat the reasonable thing to do? Is this a
>> relatively
>> easy thing for a novice mechanic? Where is the thermostat on this
>> engine?
>>
>> Thanks,
>> Tom
>>
>
12-09-2004, 05:05 PM
#6
Guest
Posts: n/a
Re: '90 V8 Quattro Water and Oil Temperature Help
So other than a faulty temperature gauge, what could account for a low oil
temperature?
Thanks,
Tom
"Jay Somerset" <jay@hotmail.com> wrote in message
news:3rehr01n6f55ighu29jkr26q53cp2rt1l8@4ax.com...
> On Mon, 6 Dec 2004 16:48:54 -0600, "GigaNews" <tom.quinn@adherentlabs.com>
> wrote:
>
>> My water and oil temperature gauges are both reading 60-65C. From what
>> I've
>> gathered, the water temperature should be higher, around 90C. I assume
>> the
>> water and oil gauges should read similar temperatures and since they do,
>> I
>> assume they are correct.
>
> Wayter temp should be near 90C when the engine is hot. My '90 Audi-90 had
> chronically low water temp reading and very slow warmup after about the
> 4th
> year during the winter. I suspect that the thermostat was stuck open.
> It's
> a bitch to change on the -90. You have to remove a bunch of stuff to get
> the housing off.
>
> Oil tempertature should be a bit higher. Between 200-250 F (95-120C) is
> about right when the engine is fully warmed up. You always want the oil
> to
> be close to or above the boiling temperature of water, so that any
> condensation in the crankcase is eliminated when the engine is running.
>
>>
>> Is checking the thermostat the reasonable thing to do? Is this a
>> relatively
>> easy thing for a novice mechanic? Where is the thermostat on this
>> engine?
>>
>> Thanks,
>> Tom
>>
>
temperature?
Thanks,
Tom
"Jay Somerset" <jay@hotmail.com> wrote in message
news:3rehr01n6f55ighu29jkr26q53cp2rt1l8@4ax.com...
> On Mon, 6 Dec 2004 16:48:54 -0600, "GigaNews" <tom.quinn@adherentlabs.com>
> wrote:
>
>> My water and oil temperature gauges are both reading 60-65C. From what
>> I've
>> gathered, the water temperature should be higher, around 90C. I assume
>> the
>> water and oil gauges should read similar temperatures and since they do,
>> I
>> assume they are correct.
>
> Wayter temp should be near 90C when the engine is hot. My '90 Audi-90 had
> chronically low water temp reading and very slow warmup after about the
> 4th
> year during the winter. I suspect that the thermostat was stuck open.
> It's
> a bitch to change on the -90. You have to remove a bunch of stuff to get
> the housing off.
>
> Oil tempertature should be a bit higher. Between 200-250 F (95-120C) is
> about right when the engine is fully warmed up. You always want the oil
> to
> be close to or above the boiling temperature of water, so that any
> condensation in the crankcase is eliminated when the engine is running.
>
>>
>> Is checking the thermostat the reasonable thing to do? Is this a
>> relatively
>> easy thing for a novice mechanic? Where is the thermostat on this
>> engine?
>>
>> Thanks,
>> Tom
>>
>
12-09-2004, 05:05 PM
#7
Guest
Posts: n/a
Re: '90 V8 Quattro Water and Oil Temperature Help
So other than a faulty temperature gauge, what could account for a low oil
temperature?
Thanks,
Tom
"Jay Somerset" <jay@hotmail.com> wrote in message
news:3rehr01n6f55ighu29jkr26q53cp2rt1l8@4ax.com...
> On Mon, 6 Dec 2004 16:48:54 -0600, "GigaNews" <tom.quinn@adherentlabs.com>
> wrote:
>
>> My water and oil temperature gauges are both reading 60-65C. From what
>> I've
>> gathered, the water temperature should be higher, around 90C. I assume
>> the
>> water and oil gauges should read similar temperatures and since they do,
>> I
>> assume they are correct.
>
> Wayter temp should be near 90C when the engine is hot. My '90 Audi-90 had
> chronically low water temp reading and very slow warmup after about the
> 4th
> year during the winter. I suspect that the thermostat was stuck open.
> It's
> a bitch to change on the -90. You have to remove a bunch of stuff to get
> the housing off.
>
> Oil tempertature should be a bit higher. Between 200-250 F (95-120C) is
> about right when the engine is fully warmed up. You always want the oil
> to
> be close to or above the boiling temperature of water, so that any
> condensation in the crankcase is eliminated when the engine is running.
>
>>
>> Is checking the thermostat the reasonable thing to do? Is this a
>> relatively
>> easy thing for a novice mechanic? Where is the thermostat on this
>> engine?
>>
>> Thanks,
>> Tom
>>
>
temperature?
Thanks,
Tom
"Jay Somerset" <jay@hotmail.com> wrote in message
news:3rehr01n6f55ighu29jkr26q53cp2rt1l8@4ax.com...
> On Mon, 6 Dec 2004 16:48:54 -0600, "GigaNews" <tom.quinn@adherentlabs.com>
> wrote:
>
>> My water and oil temperature gauges are both reading 60-65C. From what
>> I've
>> gathered, the water temperature should be higher, around 90C. I assume
>> the
>> water and oil gauges should read similar temperatures and since they do,
>> I
>> assume they are correct.
>
> Wayter temp should be near 90C when the engine is hot. My '90 Audi-90 had
> chronically low water temp reading and very slow warmup after about the
> 4th
> year during the winter. I suspect that the thermostat was stuck open.
> It's
> a bitch to change on the -90. You have to remove a bunch of stuff to get
> the housing off.
>
> Oil tempertature should be a bit higher. Between 200-250 F (95-120C) is
> about right when the engine is fully warmed up. You always want the oil
> to
> be close to or above the boiling temperature of water, so that any
> condensation in the crankcase is eliminated when the engine is running.
>
>>
>> Is checking the thermostat the reasonable thing to do? Is this a
>> relatively
>> easy thing for a novice mechanic? Where is the thermostat on this
>> engine?
>>
>> Thanks,
>> Tom
>>
>
Thread
Thread Starter
Forum
Replies
Last Post
dradman
A4-B6 - (Typ 8E/8H, 2001–2005)
10
11-17-2010 12:37 AM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
