fail safe mode??
03-18-2008, 04:32 PM
#1
Audi Forum - Posts like an A1
Thread Starter
Join Date: Sep 2007
Posts: 4
fail safe mode??
I drive a 2004A4 1.8T CVT- the transmission letters flashed on display today, pulled over, hauled out the manual and discovered that the car went into fail safe mode. Is this worthy of a $100 diagnosic plug in at the dealership? Drove it for an hour or so after and no problems.
07-07-2008, 04:34 PM
#5
Audi Forum - Posts like an A1
Join Date: Jun 2008
Location: Ohio
Posts: 2
Re: fail safe mode??
Just FYI for anyone else who gets a 'failsafe' mode.
My 2004 A4 CVT went into failsafe also. This was indicated by the dashboard (the PRND indiator flashes) and slow acceleration. It exhibited no signs of a mechancial problem (no jerking or bucking) so the dealer decided it was electrical. Evidently there are enough mechanical problems with the CVT that the dealer personnel are very familiar with how that problem manifests itself.
The car spent about 2 1/2 weeks at the dealer while they replaced one control after the next. They were trying to avoid replacing the entire control unit which they eventually did.
That was USD$2,300. And it took so long because Audi was backordered on the part. Evidently another frequent repair item.
Once that was replaced, it has worked fine.
My 2004 A4 CVT went into failsafe also. This was indicated by the dashboard (the PRND indiator flashes) and slow acceleration. It exhibited no signs of a mechancial problem (no jerking or bucking) so the dealer decided it was electrical. Evidently there are enough mechanical problems with the CVT that the dealer personnel are very familiar with how that problem manifests itself.
The car spent about 2 1/2 weeks at the dealer while they replaced one control after the next. They were trying to avoid replacing the entire control unit which they eventually did.
That was USD$2,300. And it took so long because Audi was backordered on the part. Evidently another frequent repair item.
Once that was replaced, it has worked fine.
07-11-2008, 09:53 AM
#6
Audi Forum - Posts like an A6
Join Date: Nov 2006
Posts: 947
Re: fail safe mode??
Just FYI for anyone else who gets a 'failsafe' mode.
My 2004 A4 CVT went into failsafe also. This was indicated by the dashboard (the PRND indiator flashes) and slow acceleration. It exhibited no signs of a mechancial problem (no jerking or bucking) so the dealer decided it was electrical. Evidently there are enough mechanical problems with the CVT that the dealer personnel are very familiar with how that problem manifests itself.
The car spent about 2 1/2 weeks at the dealer while they replaced one control after the next. They were trying to avoid replacing the entire control unit which they eventually did.
That was USD$2,300. And it took so long because Audi was backordered on the part. Evidently another frequent repair item.
Once that was replaced, it has worked fine.
My 2004 A4 CVT went into failsafe also. This was indicated by the dashboard (the PRND indiator flashes) and slow acceleration. It exhibited no signs of a mechancial problem (no jerking or bucking) so the dealer decided it was electrical. Evidently there are enough mechanical problems with the CVT that the dealer personnel are very familiar with how that problem manifests itself.
The car spent about 2 1/2 weeks at the dealer while they replaced one control after the next. They were trying to avoid replacing the entire control unit which they eventually did.
That was USD$2,300. And it took so long because Audi was backordered on the part. Evidently another frequent repair item.
Once that was replaced, it has worked fine.
07-11-2008, 07:36 PM
#7
Audi Forum - Posts like an A1
Join Date: Jun 2008
Location: Ohio
Posts: 2
Re: fail safe mode??
They gave me a loaner (Toyota Corolla, awful little car) the whole time so I can't complain about their treatment (especially since I didn't even buy the car there.)
Thread
Thread Starter
Forum
Replies
Last Post
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
